>>> NOW INCLUDE STANDARD Red Backlight for DMM-1 display and labels
Our DC or AC distribution panels will delight you...No apparent screws! We use circuit breakers holding bars and screws are all covered with recessed polycarbonate facings and labels for a clean look and attractive design.
Our famous DMM-1 Battery Monitor is integrated in the main DC panels for informative DC system Voltages and Separate Charge/DischargeCurrent flow.
Include All indicator lignts for status of each circuit, standard marine grade Carlingswitch breakers, prime quality Epoxy coated aluminum panels, labels backlight, copper bus bars, Irridite aluminum or Nylon standoffs, 316 grade stainless steel screws will provide years of service and protection.
All at a very competitive pricing, Best Quality/Price ratio on the market, with just the authorized reseller-installer in the line or direct purchasing.
Look and compare Deluxe Microlog Panels features:
• Integrated DC Voltage / Current monitoring with the DMM-1
• Small physical format for easy installation or refit
• Powder Epoxy paint coated 6061-T6 Aviation Aluminum
• Marine Grade Carlingswitch Breakers
• Special Breaker holding bar system for easy add or removal
• Recessed Polycarbonate Lexan facings hiding screws for nice look
• Red Backlight (Green optional) for DMM-1 display and labels
• Optional left side hinge
• Include all Power Indicators Yellow lights (LEDs)
• Integrated Negative or Neutral+Ground (AC) Bus Bars
• Silver plated wiring with Teflon jacket
• Stainless steel hardware for marine environment
• Easy to install and operate
• Two year limited warranty
• Best Quality / Price ratio on the market
Dual 30 Amp Breaker
3 x 15 Amp Breakers
3 x Bus bars for connections
7 yellow indicator lignts
1 Red Reverse Polarity indicator lignt
Backlight on labels
30 Standard AC labels kit
Dimensions: 7.5" x 5"
OPTIONS:
3 extra breakers with values of your choice
>US$ 199.95
DMM-1 DC System Monitor
9 x 15 Amp Breakers
3 x Bus bars for connections
12 yellow indicator lignts
Backlight on display and labels
30 Standard DC labels kit
Dimensions: 7.5" x 9"
OPTIONS:
3 extra breakers with values of your choice
SWK-225 or SWK-205 for AMPs measurement (see below)
HG-7 left side Hinge
>US$ 459.95
5 x 15 Amp Breakers
2 x Bus bars for connections
8 yellow indicator lignts
Backlight on labels
30 Standard DC labels kit
Dimensions: 7.5" x 5"
OPTIONS:
3 extra breakers with values of your choice
>US$ 179.95
Dual 30 Amp Breaker
7 x 15 Amp Breakers
3 x Bus bars for connections
11 yellow indicator lignts
1 Red Reverse Polarity indicator lignt
Backlight on labels
30 Standard AC labels kit
Dimensions: 10.5" x 5"
OPTIONS:
3 extra breakers with values of your choice
>US$ 279.95
9 x 15 Amp Breakers
2 x Bus bars for connections
12 yellow indicator lignts
Backlight on labels
30 Standard DC labels kit
Dimensions: 10.5" x 5"
OPTIONS:
3 extra breakers with values of your choice
>US$ 259.95
DMM-1 DC System Monitor
17 x 15 Amp Breakers
3 x Bus bars for connections
20 yellow indicator lignts
Backlight on display and labels
30 Standard DC labels kit
Dimensions: 10.5" x 9"
OPTIONS:
3 extra breakers with values of your choice
SWK-225 or SWK-205 for AMPs measurement (see below)
HG-10 left side Hinge
>US$ 629.95
>All US$ 14.95
BK-5: 5 Amps marine breaker
BK-10: 10 Amps marine breaker
BK-15: 15 Amps marine breaker
BK-20: 20 Amps marine breaker
BK-30: 30 Amps marine breaker
Anodized Black Aluminum Hinge will fit panels on left side
Comes with Magnetic SNAP closure and hardware on right side
HG-7: Hinge Option for 12DC-DMM Panel. >US$ 29.95
HG-10: Hinge Option for 20DC-DMM Panel. >US$ 29.95
DMM-1 Shunt and Wiring kits:
A Dual Shunt is necessary in order to measure amps with In-Panel DMM-1 battery monitor (you may purchase just the panel if you ONLY need Voltage measurement and Alarms).
Shunts are an accurate, very low resistance resistor which is placed "in line" with the wire carrying the current to be measured. It is usually placed in the negative wire from the battery bank, such that all the current going into the battery (charging) and out (discharging) must pass through them. (It also could be placed in series with the negative wire coming from a solar array--or other charging source--in which case it would measure only the solar array or wind current. The shunt needs to be placed near the batteries; since these wires carry very high currents the wires from the batteries must be kept short to minimize electrical losses.
| SWK-205 Shunt and Wiring kit for Panel DMM-1: The SWK-205 Shunts and Wiring kit is required if you need to measure current up to 135 Amp. Continuously. Users with alternators over 135A and 1800-2000W inverters should use SWK-225. Kit includes: Dual 200 Amp. shunts which are made with naval specification brass. |
 |
| Shunts Specifications: |
|
|
135 Amp.
|
|
200 Amp.,10 sec/min. MAX
1000 Amp. Surge,1 sec/min. MAX (Derating as ambianttemperature rise) |
|
5.50" L. x 1.50" W. x 1.50" D
14,0 cm x 3,7 cm x 3,7 cm. |
| SWK-225 Heavy-Duty Shunt and Wiring kit for Panel DMM-1: The SWK-225 Shunts and Wiring kit is required if you need to measure current up to 200 Amp such as Hi-Amp alternators or 1800-2000 W. inverters. Kit includes: Dual 200 Amp. shunts which are made with naval specification brass. |
 |
| Shunts Specifications: |
|
|
180 Amp.
|
|
280 Amp.,15 sec/min. MAX,
2000 Amp. Surge, 1 sec/min. MAX (Derating as ambiant temperature rise) |
|
7.00" L. x 1.70" W. x 1.50" D
17,9 cm x 4,5 cm x 3,9 cm. |
Shipping Extra requested:
Please Add the following shipping extra for Express mail in US or Canada.
Air and International will need more (send an email for estimate)
US$ 10.00
